Where To BuyThe surface shall be cleaned thoroughly of all contaminants like dust, rust, traces of curing compound, oil and grease. Where moss or lichen is present, remove sheets. Cut and reseal blisters in asphalt or roofing. Old concrete and steel must be structurally sound prior to application. Light mechanical grinding/grit blasting/high pressure water jet may be used to clean the surface of all the contaminants depending on the degree of contamination on the surface to be coated.
AquaShieldPro RBE 3505
Share
Non-fibrated, solvent free, flexible rubberized, vapour barrier, liquid applied bitumen emulsion coating
In stock
Only %1 left
SKU
ASPRBE3505
| DATA | RESULT |
| Colour | Thick viscous Dark brown (liquid). Black (dry) |
| Density (g/cm³) @ 25º C(ASTM D 1475) | 1.05 ± 0.05 |
| Solid Content(ASTM D2369-10) | 35% ± 2 |
| Rubber Content | 5% |
| Wet film thickness | 400 microns |
| Touch dry time | 30-45 minutes |
| Drying Time @ 25º C | 6–8 hours per coat |
| Overcoating Time | 4 - 24 hours |
| Application Temperature | From +5º C to +55º C |
| Service Temperature | From -10º C to +85º C |
| pH Value | 10-11 |
| Flash Point | Non-flammable |
| VOC content | < 30 g/ liter |
* All values given are subject to 5-10% tolerance
* Properties listed above are only based on controlled laboratory samples and tests: Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.
®=Registered trademark of the North Group.
Description
AquaShieldPro RBE 3505 is suitable for the treatment of concrete, asphalt, metal, roofing felt and other similar roofing surfaces whether flat, sloping or vertical. Where added protection is required on roofs, the product may be used in conjunction with a reinforcing fabric
Additional Information
| Applicable Standards/ Compliance: | Packaging: | Colours: | Coverage/ Yield: |
| Complies with the specification requirement of ASTM D2939 |
20 litres pail & 200 litres drum | Dark brown (liquid) Black (dry) | Typical coverage rate of 3 to 5m²/ liter depending on density, surface porosity, surface profile, variations in level or wastage etc. |
Typical Applications
- General damp-proofing of concrete, asbestos cement sheets, roofing felts, wood etc.
- Protective coating for cladding works to prevent infiltration of vapour and moisture into the building structure.
Benefits
- Single component, solvent free
- Cold applied, no heating required
- Suitable for new and old concrete
- High rubber content - 5 %
- Reduced chloride penetration
- Vapour permeable allows substrate to breathe
- Resistant against chloride and sulphate ions.
- Non- slumping
- Easy application due to paintable consistency
- Environmentally friendly. Low VOC.
- Seamless/joint free
- Has good adhesion to most building substrates
Substrate Preparation
Product Preparation
The drum should be rolled on the ground back and forth before decanting material. Stir the contents of the drum thoroughly prior to application
Product Application
The application can be done with a roller, brush or airless spray. Two or more coats must be applied to ensure a durable finish. Apply the coating at a coverage rate of 1 to 4 m²/ litre /coat, depending on the dry film thickness required. On vertical areas, it is recommended to apply the coating in multiple layers in order to avoid sagging of the heavy bodied coating. Subsequent coats shall be applied only after the previous coat dries off completely and shall be applied at right angles to the previous coat. Clean dry sand may be broadcasted onto the wet coating to provide a key for the subsequent coats and achieve a greater dry film thickness. Care shall be taken to ensure that the first coat is not punctured during the application of the second coat. However, if the coating is damaged, the area can be readily over coated provided the surface preparation is done properly.
AquaShieldPro RBE 3505 may be applied to damp but not wet surfaces, dampen brushes before and occasionally during use to avoid clogging and ease application. During hot, dry weather application may be assisted by dampening the surfaces to be treated.
Others
Cleaning:
Clean all tools immediately after use with clean water. Hardened material can be cleaned with a solvent.
Protection:
Protect floors to withstand light foot traffic for at least 24 hours after installation. Stepping boards may be used after 24 hours when occasional stepping on the floor is unavoidable.
Write Your Own Review